I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
We want to set Tx power of +3dbm i followed the procedure as mentioned in following ticket:
I set the high voltage in network core main as following:
we...
Hi,
I'm able to select the nRF21540_nRF52840DK board for my project and I'm wondering how command the nRF21540 using the I/O pins and the SPI port. Do you have any examples...
I have to make a connection from a central_uart to 4 periperal_uart every 60ms Sending 30 byte .
I Have to make a polling of all the peripheral every 60ms.
I know that...
Device: nRF52811
Board: custom (EYSNSNZWW module is used)
SDK: 16.0.0
SoftDevice: S112(v7.0.1)
Sample Project: ble_app_uart
Hello,
Is it possible to read BD...
I have a custom board based on nRF52840 with some custom peripherals : LEDs, buzzer, buttons, etc
To get my app working I copied the nrf52840dk_nrf52840 board from the 1...
Hi,
I started using the Nrf5340-DK with the openthread cli sample. It works fine, and now I'd like to move the main UART to pins P0.24 and P0.26.
To do so, I created...
Hello, I've been trying to migrate my code which uses NRFX SPI functions to NCS 2.0
The code compiles just fine on NCS 1.9, but after migrating to NCS 2.0 I noticed that...
I have just been hired to this company and they have assigned me to repair some of their defective modules. The modules are BL651 with what I believe to be nrf52810 processor...
Hi,
is there a driver available for the VM3011 microphone that comes with the Thingy:53?
The chip has some power-saving and wakeup features that are configured using I2C...
Hi,
We are having some issues communicating with a Winbond W25Q64 flash memory. Using the standard SPI Zephyr drivers an attempt to get the Manufacturer ID returns 0xDC...
Hey!
I am working on a zigbee asset tracking system for my thesis. Got myself 3 nrf5340 boards and a sniffer.
Unfortunately i can't manage to get started with zigbee...
Hi everyone!
I have recently been trying to flash the 'blinky' zephyr sample to the nRF5340 Application Core on the R4D4 Control Board. I am yet to have any success, by...
Hi there
I'm using Asset tracker v2 as a base for my application with AWS, however I wanted the FOTA to download to external flash, as the Asset tracker application is large...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 with MCUBoot and want to upload firmware updates for the application core using mcumgr.
I use the hello_world sample in...
We are migrating from Modem firmware version 1.2.x to 1.3.x. Since it is now possible to enable LTE and NBIOT both using the following XSYSTEMMODE configuraton:
How does...
