Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi
I am currently running and adjusting the zephyr echo_bot uart sample on my nrf9160 DK. Currently , the sample makes use of UART0 to send a receive information which I...
I'm trying to connect a Thingy91 to the nRF cloud using just in time provisioning. I'm using MoSh. Here is the error:
mosh:~$ cloud_rest jitp Performing JITP... JITP device...
Hello,
When I change the optimization for a project to NO_OPTIMIZATIONS or DEBUG_OPTIMIZATIONS in the configuration (prj.conf), I always go in the hard fault handler ...
Hello,
i have a Nordic nRF52840DK and a Qorvo DWS3000 combination. I´m using SDK7.0.2, Segger Embedded Studio 5.10a and J-Link 7.58b.
I want to combine the ble_app_uart_c_pca10056_s140...
Can you please explain how NRFX_SPIM_FLAG_RX_POSTINC works? My data keeps always being loaded into the same address. Here is my code snippet:
uint8_t tx_buffer_MAG[1]...
I am developing a product with nRF52832 in which we need to use the COMP module. We need to route the RESULT signal directly to the RX input of the UART, or to an output of...
Hello,
after upgrading to SDK15 and using the new crypto functionality I experience some weird behaviour during bonding.
Our SW is the peripheral and I am starting the...
We would like configure our device with a public addr instead of the random as is default for NCS/Zephyr. We are currently on Zephyr v3.1.99 and NCS 2.1. I have tracked down...
Hi, https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.1.0/nrf/ug_tfm.html#limitations states that "Firmware Update Services" are not supported. Does it mean that in case...
Hello,
I have compiled the Zigbee ZBOSS NCP HOST on an ARMv7 (32-bit) architecture according to the docs ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/zboss/3.11...
Hi all, I've searched through the devzone but unfortunately my issue is never mentioned.
The problem is: my nRF51 project is converted to a nRF52 project. Pins are all re...
We have a need to use 802.15.4 multiprotocol with BLE, we currently use the 52840 for several products. This uses older SDKs and the 802.15.4 Radio driver with our own MAC...
nRF5 SDK SD140 Using the nRF Connect Android app with the DFU utility, looking at the log I send the Enter Bootloader request and get a thumbs up back (op code = 1, status...
