I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello all,
I was programming the nrf9160 SiP using esp32 over UART and wanted to know how do I connect ESP32 to the nrf9160 SiP and upload the code through ESP32 over to...
SLM returns ERROR after AT#XSOCKETOPT=1,51 NRF_SO_RAI_LAST https://github.com/nrfconnect/sdk-nrfxlib/blob/main/nrf_modem/include/nrf_socket.h#L218
SLM returns OK for AT#XSOCKETOPT...
Hello I am using I am NRF SDK version 1.8.0 and nrf-zephyr v2.7.0-ncs1 (If a soultion exists on newer a rev, willing to upgrade now, otherwise it will happen some time in...
When PIN=0 P0.00 is used it doesn't work (No error message or failing, i also tried several other ports), no toggling output. The code works with PIN=28 (P0.28=LED1), led...
It is properly pointed to in the emProject file, and the SES IDE is able to locate and open it in file explorer.
I upgraded the liboberon to 3.0.8:
When I previously...
I have a successful build over my i2c application but, I do not get any text output on the console. So, to check I tried to build a new hello world project and run it but...
I'm attempting to use the "powf()" function in a Zephyr thread.
When I try to run:
LOG_INF ( "powf: %f" , powf ( 2.0f , - 8.0f ));
the result is "inf". (Code compiles...
After intsalling nRF Connect SDK 10.18.0 on an Apple M1 running macOS Monterey 12.6, I can't use nrfjprog at all:
❯ nrfjprog --version [error] Error in dlsym: dlsym(0x204ef57e0...
I am installing the nRF Connect SDK (on an Ubuntu 20.04 virtual machine) as described here: Installing manually — nRF Connect SDK 2.1.99 documentation (nordicsemi.com) . ...
Hi, I get the following error when I try to install nRF Command Line Tools fails to install on Ubuntu 22.04.
~/programs$ sudo apt install ./nrf-command-line-tools_10.18...
I need to install the nRF command line tolls for Visual Studio Code to work. On the download page it however shows the ARM version of the 10.18.0 Linux x86 64 deb file.
...
Hello all!!!!
Is it possible to send UART data (JSON) from ESP32 to the NRF9160 SIP and further publish the same to AWS MQTT or AWS Shadow MQTT?
It would be a great deal...
I have written a word (32 bites) in 0xFF000 using nrf_fstorage_write(), When BLEInit(), nrf_fstorage_evt() callback not trigged,
BLE_Sleept()
nrf_storage_write()
BLE_wakeup...
Here is an example main.c which you can use as an example to understand corectly how to use the GPIOTE module and toggle the 4 LEDs numbered 1-4 in the nRF52 DK. Forget about...
