Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi!
Basically, what it says in the title.
Datasheet mentions that for 2Mbps mode (enhanced shock burst) spacing should be 2Mhz or more.
Does that mean that number of...
Hello everyone,
I used nRF24L01 and Arduino to jamming 3 channel advertising BLE ( https://github.com/lws803/BLE-jammer ) and my Gateway can't receive message from my door...
I am trying to develop an environment based on the prx ESB sample and add nrfx_timer.h dependencies. This is not necessarily a question specific to this setup but a more general...
Hi,
I am using SDK 17 version. The file name is ble_app_uart_pca10040 . I send to data from nRF Connect app to nRF52 DK and this data reach correctly to nRF52. But i didn...
Hi,
Now I have some custom data that I want to save in flash to ensure data not lost when power off. What should I do?
Platform: Windows 10
NCS version: 1.9.1
Boards...
Currently, I'm facing a problem, that a custom board somewhat doesn't work. The main only consists of
The problem is, that the cpu seems to wake up every (about) 500us...
Hi,
I would like to know if the following application is possible using the nRF52840. I'm open to use the nRF5 SDK or the nRF Connect SDK.
I have a base station with the...
Hello, i want to use SHA-256 to encrypt a Payload of my outgoing MQTT Messages.
I started to modify the NRF9160 MQTT Example. To test the encryption i copied Code from the...
Hi, I am trying to implement buttonless DFU on my nRF52832 on PCA100040. After using the NRF Connect app to initialize DFU, the DFU log on the app gets to the line
upon...
When I'm trying to compile the coprocessor sample (compare https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thread_tools.html#configuring-a-radio-co-processor...
Is there any simple sample application utilizing i2c communications for nrf52805?
In Visual Studio Code with installed nrf connect SDK 2.0.0 doesn't show up any code sample...
Hi-
We have implemented a custom authentication scheme using BLE and based on a successful authentication event we would like to dynamically expose an additional set of...
Hello,
Is an embedded C based implementation to serially transport firmware data to a Zephyr based MCU available anywhere?
Background:
I am working on a nRF52833 solution...
I have implemented bonding mechanism in nRF52832 firmware. But when I use nRF Connect to connect nRF52832 device sencond time. nRF Connect still request entering passkey again...
