Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Hi everyone!!! I need help with our new version of HW after validating the previous one that works.
I read some similar posts related to the GPRETREG for HOLD a GPIO while...
Hi Nordic,
We have a design where we'd like to share the 2.4 GHz antenna between WiFi and BLE.
Therefore, we need to power and configure the RF switch accordingly, before...
Hi,
currently I am using nRF52811 in one product with BLE functionality. Now I would like to use the same MCU in other product where BLE is not needed. In this case I would...
We are developing a product based on nRF52832 and we need to verify that in case of problems, the device will "fail gracefully". So we looked at implementing the ARM handlers...
I am using LSM6DSOX IMU sensor INT detection with NRF52-DK and have extra 400µA (PPK2 used) on my setup. After a few days of nightmares I finally found that this is related...
Hi,
I'm using nRF Connect SDK v1.9.0
We're working on firmware running on an nRF9160 with TF-M enabled. We need to link with a library to is built with hard-float, so...
Hi,
i want to read temperature sensor value inside the nrf soc on bl653 board. while checking there is a file inside ( \zephyr\drivers\sensor\nrf5) this path. how to configure...
Hi,
I am working on DFU-OTA example. am looking for example , which will help me to copy image from slot1 to slot0 without using scratch pad. it has to override the image...
Hello Team,
I am using the ble_app_hrs_rscs_relay example where NRF52 acts both as a central and peripheral. My question is that when I remove the heart sensor Polar H10...
Hi,
I am working on DFU-OTA sample as suggested in this link. https://devzone.nordicsemi.com/f/nordic-q-a/84766/sample-ncs-code-to-evaluate-dfu-ota-on-nrf52833 .
For nrf52833...
Hello,
I'm using a custom board and i actually have a problem that I never saw before : error 34 (0x22) GATT CONN LMP TIMEOUT.
I have send frames : I did my own custom...
I have a custom design with NRF9160. I try to use the debug output of the NRF9160 DK, but on the debug-out of the nrf91 DK it is not recognize (target Voltage is visible at...
we use nRF52833,SDK:S140,17.2,sometims,the device goes into trouble and the error code is 0x715.
here is the call stack:
/port.c:128 0x00027482 PendSV_Handler
/port...
When developing a BLE device with nRF52840, the following error occurred when importing the header file for spi communication.
ERROR ['NRF_DRV_SPI_INSTANCE_0' undeclared...
I am using FreeRTOS with FatFS/SD card. SDK is nRF5_SDK_17.0.2.
If different tasks access FatFS API in different task, is it thread-safe? i.e. Task A access file A and task...
