Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I'm wanting to repetitively read the SPI buffer as a master to check a status bit. I figure there's no sense in using the DMA when I can read the SPI RXD buffer directly....
Hi
I am trying to use the two GPIO pins. One GPIO pin is configured as a input and connected externally to a button.
The second is configured as an output pin. I want...
I am trying to complete the course "nRF Connect SDK Fundamentals" using a nRF52840 DK board (version 3.0.0) connected to a Mac Mini (Intel processor) running macOS version...
Hello,
I'm experiencing high current consumption with Zephyr OS. I'm using SDK 3.1.0 and the device still draws about 900 µA, and I don't know why. Although I have a custom...
Hi all, I am going through the beginner course and am using the MPU-6050 over I2C. I am able to communicate with the board where I get the WHO_AM_I. I can also read from the...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
Hello,
I want to have 2 applications running on nrf5340 CPUAPP (nothing on CPUNET) with app1 in flash and app2 (in RAM) getting launched by app1 once placed in RAM as a...
After switching to the BLE advertising module in SDK 16.0.0 (on an nRF52 board) and using it for over 3 months I am now discovering that no matter how I configure the advertising...
My firmware is blocked on custom board until RTT connects: Code hits and blocks on a printf. This doesnt happen when using an NRF5340, but does with NRF5280. Just trying to...
Hello, I am using v3.1.0 of the nRF SDK with a nRF52840-DK board.
I would like to run the "Counter RTC Driver Sample" (nrf/samples/zephyr/drivers/counter/alarm). The README...
I am updating our production tools and starting by simply trying to program the Thingy91 (or DK) with the following example from the internet. I keep getting timeout errors...
Hi Team,
I have configured I2C0 for reading data and sending iqs323 and iqs7211a. i have configured overlay file according pin conjuration which is below.
Pin configuration...
HI
Currently using NRF54L15 with NCS v3.0.0 and the periodic_sync_conn sample. I have created sysbuild.conf and added SB_CONFIG_BOOTLOADER_MCUBOOT=y. After compilation,...
Hi all,
I’m working with an nRF-based board and need to via software disable the internal DC-DC converter and use the LDO exclusively for testing purposes. I’m unclear on...
