I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I'm seeking clarification on what all can be ran on the network core. In the Network Core introduction section of the Working with nRF53 Series page, it mentions `the network...
Hi everyone,
As I mentioned in the subject, how many time do we wait for sending Start and Disable commands after Ready and End interrupts in transmit sequence of nRF52840...
hi, i have read nrf52832/40 product specs. i want to know about system off and system on modes. i am not getting what they mean pls explain in simple words.
infocenter.nordicsemi...
I want to use the usb dfu along with the buttonless ble dfu, how can I do so? I want to use the usb to have dfu and also work as a vitual com port? Can I simple merge both...
Hello
Can you provide customer with the API of the attachment( nRF_DTM.exe application)? They want to integrate this application into their mass production tools.
Hi everybody,
I am working with two custom boards with nrf52840 chip, using the examples of UART central/peripheral.
I set power TX of connection exactly as the example...
I have got the nrf5340dk,then i using the SES IDE of windows。I open the sample named "peripheral_nfc_pairing sample",and build the solution,then debug it .After those steps...
I am attempting to advertise two sets, one using coded PHY and one using 1M, currently using the master NCS branch (post v1.7.0-rc2 tag). This is on a custom board with an...
Hello,
I have got the exact same issue as described here: https://devzone.nordicsemi.com/f/nordic-q-a/58275/zigbee-reporting-not-work-while-using-multiple-endpoints/236706#236706...
I'm running FreeRTOS with default tickless idle mode (CPU is woken up by SysTick interrupt) on NET_CPU core.
If the TAD_S module (Trace and debug control) is not enabled...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
