Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi
Is there a undocumented register to control the CC1/CC2 inputs?
Many power-banks switch off it's output if the current falls below a certain value (e.g. when the devices...
I am wanting to use the castellated pinouts on the nRF7002 expansion board.
I have the nrf7002eb.overlay file open and it has defined two pins that do not make sense to...
我们自己用nRF54L15做了一个硬件，和Android BLE调试助手链接都正常， 和电脑端连接大概有30%的概率能连接成功 我用的是主要报错是Failed to subscribe to characteristic: 6e400003-b5a3-f393-e0a9-e50e24dcca9e. 订阅读取数据特征失败
Hi
When l was using the function ble nus_c_string_send0 for datatransmission, an error occurred. The error code was 0x00000008.And at this point, the system resets.l don...
name:
Code:
Log1：
When the storage capacity is 64 entries, continuously reading 32 of them takes about 2 seconds.
After changing the path, run the write and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I need...
I cloned a project( https://github.com/pstrueb/hci_uart ) from GitHub and added conf files to the project. How do I know that these conf files were compiled correctly?
Hi : Here is the initialization in C:
#define SPIS_INST_IDX 22
static nrfx_spis_t spis_inst = NRFX_SPIS_INSTANCE ( SPIS_INST_IDX );
void device_spis_init...
Hi,
I keep running into an error with the following output when building the configuration for nRF52840. I thought my prj.conf would fix the issue, however, the error still...
This isn't really a problem, just wanted to bring it up in case it is helpful. I'm using the nRF Connect for VS Code Extension with nRF Connect SDK v3.0.2. I have a nRF 52...
I have upgrade to nRF Connect for Desktop v5.2.0
Under the Desktop, I also upgrade Programmer APP to v4.6.2
and JLink to v818. Added the installation folder at the top...
Sometimes is interesting to see more details of each layer.
I remembered some times ago, that SoftwareDefinedRadio (SDR) comes with a lot of possibilities at a very low...
I have a custom board with nrf52832 and LIS2DW12. I was trying to poll accelerometer data, but getting "app: fetch failed: -134" error" My dts file is:
&i2c1 {
compatible...
