Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hey all! Today I tested the Asset Tracker App V2 (NCS v1.6.0) with the AWS implementation of the Cat Tracker App.
The rollout was totally fine at the end, and also the App...
Dear Nordic Team and Community!
I want to rise up the question again how to update an advertising message, especially the device name (on nRF52840Dongle, S140, 10059). I...
,i use a nrf52840dk_nrf52840 to run once a nrf5340dk_nrf5340 board's code , I change board name from nrf5340dk_nrf5340_cpuapp to nrf52840dk_nrf52840, change xxx .overlay from...
Hello,
I use central_uart (nrf52840dk) and peripheral_uart (nrf52833dk) examples, NRF Connect SDK v1.6.0
I want to send more than 20 bytes of data,
So, I increase UART_BUF_SIZE...
Hello,
I am using the nrf52840 controller for the development ,i want to read the value from 2 channel of ADC . I just gone through the SDK example code of
SAADC, here...
Hi All,
I was trying to transmit a bare-metal minimal C program to send a raw ADV_SCAN_IND PDU using nrf52840 dev board. Code is listed below:
Here is the linker script...
I'm currently building a device that has the following functionality:
1.) wake from sleep mode and wait 5 seconds for a potential button press
2.) if the button is pressed...
Hello,
I'm trying to debug an issue where a function I wrote that should only be called under a specific condition is calling in an infinite loop whenever the program runs...
Hi, I'm using nRF52805 S112 for my BLE project. I'm using an internal RC ocillator. I would like to ask something about the clock.
1) NRF_SDH_CLOCK_LF_RC_CTIV =16 and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello,
I am working on using the open_bootloader with our application and running into a problem.
We are using the GP_REG to jump from our application back to the bootloader...
Hello,
I'm using the following code to loop through the flash memory sequentially and send records created by the flash_fds example:
The data stored in the records...
Hi,
How does numeric comparison works? Shouldn't both devices share parameters in order to display the same number? How can we be protected from MITM?
Thanks!
Ive added another endpoint to the OTA zigbee client example, when I run
ZB_ZCL_SET_ATTRIBUTE (ep, ZB_ZCL_CLUSTER_ID_ON_OFF, ZB_ZCL_CLUSTER_SERVER_ROLE, ZB_ZCL_ATTR_ON_OFF_ON_OFF_ID...
