Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi
The NRF52832 I used seems to have accidentally turned on the read-write protection，Cannot establish a connection using JLINK now，Is there any way to turn off this read...
Hi, We are developing a robotic product using nRF52840. I would like to know if Nordic officially supports Zephyr OS and have plans for supporting features in long term?
We used sd_ble_tx_buffer_count_get() to get maximum tx message can be sent in nrf51. However, this api is removed from nrf52840.
Is it equal to the setting of NRF_SDH_BLE_GAP_EVENT_LENGTH...
I am using NRF52840 and SDK1600. Currently, my program uses 50kB RAM memory according to Segger Embedded Studio. NRF52840 has 250kB RAM memory, so there is plenty of space...
Hi,
We are building a prototype based on the asset tracker demo application. We had interfaced different sensors on different peripherals (2 on SPI and 2 on I2C). However...
I have applied the errata 171 workaround to a zephyr code base with an MX25 chip and set the speed to 96MHz - when I run the application (engineering D silicon) with a scope...
Hi
I have used ble_beacon example to configure DK board as beacon here i wanted to pass custom data inside the code and print those array code on output debug console to...
I have an embedded Linux platform which uses an nRF9160 connected via UART. The nRF9160 has been loaded with the serial LTE modem firmware, version 1.3.1.
I've been experimenting...
Hi!
I'm developing the NRF9160 target from a raspberry Pi. The problem is that I need occasionally to perform modem firmware upgrade, and I can't figure out how to do it...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
I have add a custom characteristic in the heart rate service sample code.
The characteristic is shown on...
Hi Nordic,
I am using your official board nrf52840 to develop my application based on the ble_app_uart_peripheral example. BLE communication and the spi interfaced sensor...
Hi, I'm working with a nordic thingy:52 and SDK thingylib on Android.
The issue I'm facing is that the real sampling frequency, compared to the one indicated by the SDK...
Hello,
I try to use the ASSET_TRACKER application with NB-IoT/ Vodafone in Netherland. Vodafone uses UDP/IP datagrams protocol. is it possible to modify the asset-tracker...
So, we are using NRF52811 with external 32MHz xtal and also exeternal RTC crystal.
Every now and then we are unable to pass tests of the programmed firmware because the...
