Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
I am using now SDK 15.0 and the value of APP_ADV_DURATION is set to 18000 (180 sec)
But I saw that fromSDK15.2, it is recommended to change the value to 0 in order to get...
Hi,
We are running an application using REG1 only in DC/DC mode, REG0 is disabled. I believe we've found a small issue with our decoupling of all the power pins, but I'm...
Hello,
I am trying to connect my nRF9160 but am running into some trouble. Only LED 3 blinks for about 3 minutes and then just stays on without blinking; LED 4 never blinks...
Dears
I double the ble_nus_init as below ,I can get 2 service bouth have 2 characteritic.
as below:
err_code = nrf_ble_qwr_init (&m_qwr, &qwr_init); APP_ERROR_CHECK...
I am facing issue with programming of own developed nRF52810QFAA board. I used Pins 25 (clock) and 26 (data) along with Vcc and Gnd to flash device. I tried with two boards...
Hi, May I use slip library code for commercial? I have a project that uses an MCU communicates with an NRF52 BLE module. To upgrade program of BLE module, I flash the bootloader...
I’m mitgrating from nRF52832 TO nRF52810 and softdevice s132 to s112 and having compile issues.
I understand that NRF peripheral has been removed on the nRF52810 but I do...
This how i make it happend:
1.programe softdevice and bootloader.
2.generate app dfu package.
3.upgarde app via nRF Toolbox
4.It's running, all things is seem ok....
Hi, I've been working with SDK11, and now I have to move my project to SDK14 due to some issues with the old SDK. In SDK11 I could just use Keil's "Manage Run-Time Enviroments...
Hello,
I am trying to execute the SPI slave example from sdk15.2 on my NRF52832 Dev board (PCA10040 1.2.1).
I am using stm32f0 dev board as the master and transmitting...
Let suppose using the dynamic multiprotocol ZigBee + Softdevice application with OTA upgrade possibility. I would like to use the app_timer (along with app_scheduler) to trigger...
