Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi
I'm using pc-ble-driver-py(python2.7).
I read that python2.7 will not be maintained past 2020.
So, i want know about pc-ble-driver-py update plan.
When will the...
Hello,
We have an application based on NRF52832 which runs Nordic UART service and DFU service SDK15.2 SD132V6.0. Now, we need to add “high speed data pipe” and we are...
Hi,
I have been using nRF24 in many projects with Arduino. So far quite good experience.
Now I transfer to STM32 and have a strange problem, I cannot send with STM32 as...
Hi,
Has anyone tried connecting the grove_display to the nRF9160?
http://wiki.seeedstudio.com/Grove-LCD_RGB_Backlight/
I have tried the code below
https://github.com...
Hi All,
I'm trying to understand certificate goes where from AWS-IOT to certificate.h.
when setting a new device, I have these 4 certificates:
also the ROOT CA contains...
I have a custom Characteristic in my GATT that is sending data in Notify mode every 30ms.
In my firmware I use timer to do this with something like this :
Everything...
I'm looking to test the DPPI peripheral on the dev-kit, and to that end I though a good example would be to setup the DPPI peripheral to trigger an event when a button is...
Hi, I am new in the development. I want to interface the relay withe ble module.
But not able to do that. Please any one help me to interface the relay. Thanks in advan...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
