I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I am using the secure bootloader with DFU, and the buttonless DFU service. I extracted these applications from the Thingy SDK v2.1.0. This works perfectly fine as long as...
Hi,
My problems are as follows:
SDK :nRF5_SDK_15.0.0_a53641a.
IDE:MDK 5.2.6
Chip:nrf52832 SPI0
External Flash :W25Q64
Now ,I can read the chip ID correctly ,but...
Hi,
Please find following source code.
After compiler by Keil 5.24.2, some code will not compiled,
I can see the situation by "enter debug mode, please find following...
Hi,
I am trying to develop a central device that would scan for devices that start with a prefix XYZ_, for example XYZ_1111, XYZ_1245,...
Is there some way to add a name...
Hi,
I am using esb function to implement my project, and I set "noack" condition to "true".
How can I know the destination address when I receive a packet?
Thank you...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
We are developing a BLE device that will act as a central and send data to a peripheral. To begin with, I have used the uart central example code from SDK to set up a central...
Hi, I am trying to figure out the adc example posted by Nordic Semiconductor on Github.
https://github.com/NordicPlayground/nRF52-ADC-examples
There was two examples,...
Say I have the PWM Decoder set to NRF_PWM_STEP_TRIGGERED. If I use NRF_PWM_TASK_NEXTSTEP to step through a PWM sequence, will an event be generated for each step? I would...
Hi,
I have merged ble_app_multilink_central example and ble_app_uart_c example. and function is Ok.
Central(nRF52) can connect to HM-10(ti cc254x) and communication is...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
BLE communication can...
Hello!
I am using SDK 15.0.0 with keil.
I tried to use the sample program to do BLE communication, but I have one thing in doubt.
I'm using SDK15 / example / ble_peripheral...
I’m in the process of learning the nRF52, and tries to combine the ble_app_gatts and the pin_change_int examples (using nRF52 DK, SDK 15.3 SES projects on a Win7 machine)...
Dear,
secure_boot
I tried to change baud of UART0 from 115200 to 9600
nrf9160_pca10090.overlay
and nrf9160_pca10090.dts
Then, run LTE Link Monitor of nRF Connect...
Hello
I'm using NRF52 PCA10040 board., SDK 15.2 libraries with GNU ARM GCC and Eclipse as an IDE developing FW on Windows10 x64.
I have been facing a problem trying to...
