Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
i am using this project,where can i download the origin app,soft,especially bootloader ?
the flash is been erased, i want the origin hex ,thank you
\nRF52832 pack\nRF5_SDK_14...
Hi,
Am using nrf52832 for my BLE project with SDK 15.02. I found sometimes device is not showing after disconnect, I have to reset the device manually to show the MAC...
I'm trying to update my project to use the latest S110 softdevice release. The trouble is that I have written many of my own hardware abstraction layers and they are conflicting...
Hello,
I am trying to program a nRF51 chip with a dev kit. When I install the base nRFGo Studio, it is able to detect the board but it won't read the chip because it is...
Hi,
I am experiencing an interesting case ( I am not sure if this is a problem indeed).
I have been trying to develop code for ISP1507 (nRF52832 PC10040 based) on two...
Hi ,
I have tried to test the current consumption on NRF52840-DK (PCA10056).
DCDC is enabled.
RTC is running.
No BLE is advertising.
The DK is powered via USB. ...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
Hi.
I did the secure bootloader DFU. I attained step 8 in document .
I instal softdevice and secure bootloader to flash nRF52832. After make the ble_app_buttonless_dfu...
Routing the DCC pin on the nRF52832 with the chip scale package is pretty tough. The bump is surrounded on all sides by other bumps, so I don't have room for a via in the...
Hello,
I'm using nRF Connect V2.6.1 on Windows 10, I launch " Bluetooth Low Energy V2.2.0 " that uses PCA10059 Dongle as central.
Also, I have developed a peripheral application...
There are 12 LEDs which are connected using shift register HC595 ,the module used is nrf51822(bluetooth module). I want the LEDs to go off after 3 seconds interval. My code...
Hi there,
We are having issues with our boards that uses nrf52832 chip. Our first built had this chip and everything was working fine. We built a second batch and all boards...
Hi,
In nRF52832 datasheet I found that it is having internal oscillators, like 32.768Khz RC oscillator and 64MHz RC oscillator. If it is having internal oscillators what...
Hello
Most of the time we shall use the BT TX 0dBm. In special cases when we want to increase the communication distance we may select the 8dBm mode.
For RF type approval...
