Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I'm using nrf51822 and ble_app_uart(SDK 12.3.0).
I'm sending data from my android phone.
My question is that what happen if send data before previous data is...
Hi!
I am developing application for thread on NRF52840. I've got one problem with connection stability. Sometimes some SED nodes are disappearing. Only reset makes them to...
I am using CC2541 and CC2540 (USB dongle) which will communicate with each other and transfers data. I want to know weather i can communicate to CC2541 (ble device) directly...
Hello,
We have a setup where we connect an nrf51822 and an iphone.The nrf51822 connects to the iphone,
notifies the data and disconnects roughly every minute.(This is done...
There are only HID periphral sample code in nRF52840 SDK.
It is difficult for me to implement HID central with the sample and tutorial provided.
So I want to get a sample...
Capture_Load_error.PNG
All,
I'm new to the nodic. Just now installed KEIL V5.24.2.0.'m able to compile code but not able to load it on Target.
Please find attachment...
Hello,
It doesn't seem possible to mimic a IEEE public BLE MAC address using the BLE stack provided by Noridc. But how easy is it for others to roll their own BLE stack that...
For longer than I'd like to admit, I've been trying to make an application on the NRF52832 that relays UART data to a phone. To date, I've:
Gotten the BLE_APP_UART application...
hello all：
I think sdk13.1 s132 has a bug about ANCS，
ANCS works normally only in the following two cases
1、Both the phone side and the device side do not remember...
I have a sensor with serial protocol of 7 bits data, even parity, 2 stop bits. I wanted to use uart library to interface with this sensor. But I couldn't find the settings...
Some times when I'm trying to use GDB it stop with the following information:
(gdb) file _build/nrf51822_xxab.out
A program is being debugged already.
Are you sure you...
I started to try SAADC example in SDK12.3. After setting up project in eclipse, I got two errors:
Symbol "NRF_TIMER0" could not be resolved
Symbol "TIMER0_CC_NUM" could...
Hi,
We are a group of students at NTNU looking at the possibility of creating a small device that connects to your phone and multiple other BT devices simultaneously, letting...
Hello,
This is a quick question regarding the behavior of the Power Supervisor POF warning. We implemented a fairly naive use of the POF warning where we would log an POF...
Hello I am using the NRF52832 in ESB mode. I use both VERIFY_SUCCESS() and APP_ERROR_CHECK() within my code in various places but when am I supposed to use versus the other...
