Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
Thanks for the info already provided in devzone.nordicsemi.com/.../
I'm starting a new design with size (and volume) minimization a key requirement. Couple questions: ...
I am looking at the common nRF24L01+ module PCB with integrated antenna which is available at several suppliers. See picture below:
My question is - was this PCB design...
I'm using nrf51822, sd 10 and bootlader from sdk10. I can perform DFU to my application by loading the zip file with nRF master control.
Now I performed some customizations...
Hi
nRF51 dongle is no response from master emulation. I already did erased and flashed again few times but still not resolve.
I'm also restart my PC as well but the...
Dear nordic.
I am testing with nRF51822,
and have some question about hardware stability check.
Could I check below hardware stability, during or after system initialization...
