I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I found a link
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/overview/integration.html
which says MATTER protocol support is available with nrf...
nRF5280, nRFSDK 17.0.1, SoftDevice 7.2.0
The nRF52840 data sheet describes the RADIO->FREQUENCY register this way:
And describes the legal values for it in this...
Hello,
I have an application running with a BLE peripheral and our proprietary TSCH wireless stack using an integrated radio. The hardware sharing is done through the MPSL...
It seems like most or all of the sample code contains README.rst files as their documentation. What is the preferred/suggested way to view these in rendered (i.e. not raw...
I am trying to connect an MX25R6435F NOR flash on a custom PCB to an nRF52832 running nRF Connect SDK v2.8.0 using SPI. I am currently using the devkit devicetree with some...
Hi. I'm trying to flash the Cell Fund Lesson 4, Exercise 1 app – Reading buttons and controlling LEDs over MQTT, to an Icarus IoT Board v2 using the Actinius I/O Serial Programmer...
Hye,
using the nrf 2.4.2 toolchain
i have an unsolvable problem about ble on a nrf52840 based project with imu, i2s strip led, buttons, spi speaker...
i have a classic...
Hello,
We are looking at using the DTM sample firmware for BLE tuning in a form-factor version of our product. Unfortunately, the only GPIO pins we have exposed are SWDIO...
I am using the nRF7002DK development board, which features an nRF5340 as the Host MCU for the nRF7002 chip. I am testing the " Wi-Fi TWT Sample " sample project, which allows...
I have designed a PCB using the nRF52840 microcontroller and the MAX30001g ECG sensor. The sensor requires a 32.768 kHz clock signal via its FCLK pin, as shown in the attached...
I believe I have discovered a bug in the SLM firmware. I am using SDK v2.6.1.
When running the nRF9160 in MQTT datamode, we are encountering an issue where the slm_quit_string...
I have successfully setup my nRF51822 chip with Wireshark to capture BLE packets, using the 4.0.0 release of the nRF Sniffer software (extcap folder). However, the capture...
Hi,
I am currently using nRF Connect SDK v2.5.3 and want to update to a newer version, because I want to create a board definition and I want to do it in HWMv2.
Even though...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
