Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi!
I am working on creating a Low Power mesh network and am trying to decide which communication protocol I should use with the NRF52840. There are no nodes in the network...
Hello,
I'm using NCS 2.0.1 on a nRF5340 board.
Currently I have some troubles with getting a response if I try to write a BLE characteristic from an iOS app. The write...
Hello, I am trying to disable using uart for console use Kconfig.
I am using sdk v2.0.2 (VSCode + nrf connect extension)
It works and the software works as expected. After...
Hi,
I would like to know how I can get the connection parameter in nrf connect for desktop. I want to assign the same parameter for our pc-ble-driver-py program.
Good day to all
I am at the final stages of developing a program for collecting sensor information from a UART and publishing it onto a mqtt server. Currently the device...
Hi All,
I am using nRF5_SDK_17.1.0
while building SDK example project uder the below path with SES
..\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10100_s140_ble...
Hey!
Would it be possible to use I2C and SPI simultaneously on the nRF5340? I'm using I2C/TWI for sensor data (optical based) and SPI for a DAC - need both of them operating...
Hello,
I'm doing a few power consumption tests on the nrf9160 DK with NB-IoT for a battery powered application. PSM mode works as expected but I measured a current drain...
Hello, I am looking to cheaply flash a nrf5340. This will most likely be a one-time thing, so I don't want to invest in a J-Link device.
I have an ST-LINK clone though and...
Hello Everyone,
I need help in the integration of MPU6050 with nRF52840. I know inside SDK one example is present but it worked with nRF52832DK. when I tried to build it...
Hi!
I am attempting to configure a nrf5340 dk as a central to receive BLE notifications. The code is based on the central_hr sample.
The notifications i am attempting...
I'm like 99% certain this isn't possible but has anyone tried running VS Code Server with the nRF Connect SDK?
https://code.visualstudio.com/docs/remote/vscode-server Compiling...
Hi,
1.Mode B prevents RF9160 from entering low power consumption. How to disconnect RTT from nRF9160 module in mode B
2. In normal mode A, disconnect RTT from the computer...
