Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
There are two UART interfaces in nRF52840:
We have refer to nRF52840 and nRF52840 DK materials, but we found only one UART connection reference.
We want to know how to...
Hello, team.
I have some questions about reset restriction of nrf9160.
Q1. Does the restriction timer(30minutes) still run after +CFUN=0?
Q2. What is the exact meaning...
Hi guys. I read this thread answered by Einar Thorsrud. devzone.nordicsemi.com/.../direct-advertising-example
"HID mouse example uses direct advertising, but only when it...
I am using nRF52840 dongle with raspberry pi 4 to create a thread network. I downloaded nRFconnect for desktop to flash the hex files into the dongles.
I successfully flashed...
Hello Nordic support,
I understand that BLE stack is provided in nRF5 SDK as SoftDevice hex file and the flash area is fixed for the softdevice. I would like to understand...
Hi,
I'm trying to implement a circuit using a brand new nRF52840 chip. The chip has no bootloader included yet. When I try to burn bootloader, the chip is not detected by...
Hi
1. What certification is required to sell the products developed by nRF9160 in Japan?
2. What certification is required to add an antenna to nRF9160 in Japan? Do I...
Hi,
i've developed a few application using nRF5 SDK, and
Now I'm just getting started to study nRF Connect SDK (v2.x.x) by using "peripheral uart" sample.
I thought...
Hey,
Trying to compile a custom driver for an I2C device and running into issues getting the actual DT node to link with the driver at build time.
Specifically, (because...
I use Linux with the nRF52840DK. I have three such developer boards, and only the one with the serial number 1050205291 exposes two ttyACM interfaces on Linux vs the other...
Hello,
I got several questions below:
1. Once the CTRL_AP setup was already configured below, even if NVMC.ERASEALL is set , does that mean UICR registers ( NRF_UICR...
We have been looking for a standard (in Zepyhyr or SDK) way of handling communications between our software modules (drivers, modules, threads) that generate multiple streams...
Hi,
I am currently having a project which is communicating between nrf52811 and nrf9160.
I have an issue in nrf52811 when I try to check or debug in realboard.
I already...
Hi, I am currently having a project using nrf9160. I would like to learn basic of this microcontroller from example in SDK. Which pca--- should I use for nrf9160? Thank you...
