Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I just noticed that setting any of the CONFIG_BT_CTLR_TX_PWR has no effect on the range and RSSI while advertising. Does this config actually do something? I tested...
hello,
I have a DHT11 temperature and humidity sensor connected to Raspberry Pi 4 B. I want to transmit this data from this raspberry pi to another node using 802.15.4....
Hi,
In nRF5_SDK version 15.3.0_59ac345 with nRF52840, the function nrf_nvmc_write_bytes() writes to the same 32bit word too many times.
According to the datasheet:
...
I am starting the Academy SDK course and getting my tools installed. I have VSCode installed (I have used it on many other projects and the "nRF Connect for VSCode" is installed...
Hi ,
When I set CONFIG_TFM_PROFILE_TYPE_NOT_SET=y to disable TF-M minimal mode, KMU SLOT MKEK must be empty right? When the KMU is not empty, the app will enter the tfm_hal_system_halt...
Hi! I have a Thingy:91 v1.6.0 and doing some current measurement on the device. I've disconnected the LiPo cell, and feed the Thingy from an Otii connected to the P3 (Li-po...
Hello,
I have a motion sensor with me and it has 4 pins. VIN, GND, OUT1, OUT2. OUT 1 and OUT 2 gives output voltage of 3.3V or 0.3V depending on a motion. I want to read...
Hello,
Just want to check that is there any mechanism available to check or monitor the expiry date of TLS certificate used in the project? Is there any API available so...
Hi,
I'm extremely new to Nordic (and embedded development in general), but I'm writing some code that turns on various LED colors based on input from an Android app (BLE...
Hi,
I am using mesh sdk version 5.0.0. And I am using sensor server model example to build our application on top of it. I am trying to erase the provisioning information...
Hi,
I have a couple of questions regarding the nRF52811.
1. What's the boot time of the nRF52811 from the power on to call the main() function of the bootloader? ...
Across several NRF Connect SDK versions, I have noticed that when built with the bootloader, the child image is built with the wrong environment and does not use the vendored...
Hi Nordic team,
I am working on a custom board which contains a nRF52840 BLE chip.
The board advertises with 'Nordic Template' code but not with the DFU code.
I program...
hi,
I want to use PPI function for timer trigger to PWM, but I noticed PWM doesn't have TASK_START register, please see the pictures.
how can I start PWM by timer?
...
