Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have made my own customboard with the nrf52811. For development I have used nrf52840dk.
I´m trying to program following:
I did solder one PCB by hand. It didn...
Hi Team,
I am looking for a new readily available to test on my Nordic board 52X version.
could you please share the inputs and the source code that i can test and upload...
Hello, is there a guide on what should be done to make the sample codes for the nrf52840_dk compatible with the nrf52840_dongle? If there isnt, can I please know how one can...
Hi,
we would like to set the USBD_SERIAL according to the device serial, which will be an abbreviated version of the MAC address. I've checked the code and can only find...
Hi,
I am getting a similar error. I have nRF52832 board connected to raspberry pi for flashing and debugging using openocd. As soon as openocd command is executed I start...
Hi guys. When reading the OOB pairing example,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_nfc_pairing/README.html
" This...
Hope someone can bring some clarification to me.
I am studying the principle of Shock-burst and a part of that study is to go through every step in the examples of “esb_low_power_ptx_pca10056...
In My Window 10 PC., No connected devices are shown in VS Code when nRF52840 dongle is inserted in PC USB Port.
But in Programmer, nRF52840 dongle can be found.
Device...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server
Software: ...
I'm trying to program an nRF52 on a custom PCB using the nRF52-DK and am getting an error when connecting with nRF Connect v3.6.1.
I made the following connections from...
When I add example timer to example ble_app_uart an error occurs.
I followed the template and pasted the code.
Here is my sdk_config.h
An error occurs when...
Hi,
I am programming the nRF52833 DK using the nRF Connect SDK (v2.00). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr to both boards successfully...
Hi all
I'm using the nRF52832 and I've configured P0.21 as RESET pin.
When I reset the nRF52 via P0.21 while the debugger is running, the nRF52 actually resets but it...
I am trying to implement the ble_app_hrs example from nRF5_SDK_17.1.0 and my board is nRF52840 Dongle.
After program the board, the board can advertise and I can find the...
I want to use nRF5340's GPIOTE and DPPI implementation, pull up PA_SWITCH_CTX_PIN when NRF_RADIO->EVENTS_RXREADY is triggered, and pull down PA_SWITCH_CTX_PIN when NRF_RADIO...
