I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using nRF Connect SDK with VS Code on Ubuntu 20.04. I have installed SDK using the nRF Connect for Desktop and Toolchain Manager.
When I start VS Code I get the following...
Hi, I am trying to see the connected devices by executing the "lsusb" command, these are the steps I followed:
1.- Connect USB / swith NRF power Source to USB:
2.- Click...
Our development environment extends the NCS for our 9160 and 52840 hardware. To create a command line build environment in v.1.x.x, I was able to leverage the env.cmd file...
I have migrated an application based on the peripheral uart sample, running on a Fanstel BT40 board, from nRF Connect SDK v1.6.1 to v2.0.0. The application receives one line...
Hi,
I am trying to send data to a http server, and are trying to error handle. I am looking trough the documentation on the send() funciton in the socket.h library, but...
Hi,
I have an issue with interrupts on TIMER1 on nrf5340 NETCPU. My setup involves 2 timers that are linked via DPPI, TIMER2 counting microseconds and TIMER1 counting milliseconds...
Hi!
I am currently using the ADC to take two thermistor values from 2 AIN pins. Currently we are using the 10 bit ADC but I am looking to achieve 14 bits with oversampling...
Hi Devzone
currently we found the time cost for memset has increased after the project the use NEWLIB_LIBC
inside the project , we use funcation k_cycle_get_32 to calulate...
I'm making a device that has a nRF52833 along with an IMU, SPI flash and an LED. This device is running off a CR2032 battery and, of course, we're trying to stretch the battery...
Hello. I'm making an application that sends Mqqt data to a broker using the zephyr\samples\net\cloud\mqtt_azure example. I am using the W5500 module for internet access. Everything...
We are using a design with an nrf52832 and USB-C power only socket. We are planning to overload the USBC CC connectors so that we can program via via USB for factory production...
Hi, I am able to write a string to a text file into an external SD card and read from it using below .overlay configuration. &spi2 { status = "okay"; compatible = "nordic...
The current project needs to save the ID in the programmable register and use the ID in the application image.
So I save the ID number in the URCI->OTP[0] register. When...
Hi guys. I'm using nRF5 SDK v17.1.0 ser_s132_hci example with the PCA10040 board.
Q) Does the INFOCENTER not explain the serialization examples?
https://infocenter.nordicsemi...
