Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi everyone, and thanks for all the help provided on this site !
I have tried to flash a MDBT42Q using the nrf82832-DK (PCA10040) and it works fine for simple peripheral...
Hello,
Aim : Our application uses the PC-BLE driver for serialization purpose as well as the nrfutil for DFU purpose in the same script, we switch between the two by opening...
Hi,
I am developing a BLE sensor based on nRF52840 SoC (QIAA aQFN 73). I would like to get some clarrification regarding following points while hardware design. Thanks for...
Hi there,
We intend on using the default Serial LTE Modem example on the nrf9160 in our product. We will then communicate to the modem with AT commands from an external...
I'm trying to program a nrf52832 chip with a nrf52dk board by configuration below, referred to https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using...
Hello,
Since the last update some of the includes in my files are being marked by VSCode as "cannot open source file xxx (1696)"
The application compiles fine...
Hi! The nRF9160 has a nice, accurate LFXO integrated. I'm assuming that it's also active most of the time anyway to provide timing for the modem (assuming one is using the...
Hi, I have the following questions. Please help me answer them: Using the protocol stack of the above version, one master and two slaves are disconnected when reconnecting...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
I'm interested to know if can I have the Zigbee protocol on the nRF5340 microcontroller and use a web browser (from my phone for example) and get a http page from the MCU...
Hi,
I've connected in BLE two devices
- NRF52840 DK as "central", connected to PC via nRF Connect For Desktop v3.11.0 -> Bluetooth Low Energy v3.0.1 - NRF5340 based custom...
Hello Sir/mam,
I am working on BMS I want to prefer nrf9160 dk board for my project . I want know is there any way or document available for communicate with Modbus or can...
Hi there, I have compiled the hello world example of Zephyr and flashed my NRF 5340 DK successfully. Now when I want to use the COM port to see the results on my ubuntu I...
I have issues running the upgrade of nRF Conenct (too old linux version to run nRF Connect 3).
I tried to downgrade, downloaded v2.6.2 appimage from https://github.com/NordicSemiconductor...
I am using nRF Connect Toolchain v 1.9.1 on a nrf52832 processor and I am not able to access any of the GATT characteristics beyond the 6th characteristic that I define. The...
