Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi There,
I am presently running a BLE peripheral example on a custom board with SD Card data logging functionality, The SD Card library has worked fine until now , Since...
How to print a float value in segger embedded studio?
I am using nrf5_sdk17.1.0 version
I have used the below statement but it is outputting 0 only always.
NRF_LOG_INFO...
Hi,
I am using nrf52832 for a battery powered PIR sensor. I want the device to be awake only when in it detects motion. Can anyone guide me to use the lpn example in the...
I am using nRF52840 SoC for NCP/RCP application at the border router side, and nRF_Connect_SDK_v1.9.1 for NCP/RCP application development. My border router is my custom gateway...
Hey!
I want to try my SIM but I can't start the modem. Each command related to the modem that I execute gives me this error. I tried different firmware, but I can't upload...
I am looking for a BLE module to develop a product which will be used to track location and speed, with at least 2Hz frequency.
Requirements:
- Precision (location must...
Hello,
I would like to use the nRF5340 DK external debug port to program Thingy:91 as shown in Thingy:91's Getting started guide.
I believe that it is possible to use...
Hi
I want to use Sqrt() function from math.h but in my application it triggers some errors. Kindly guide me on how to properly include the math.h library into my application...
Dear Mr, Mrs
I was wondering how many flash size is left to the application firmware for a nrf52810 using both central & peripheral.
As far as I undestood, I need a s132...
Hi! I'm working on this particular project and the next step that I need to solve is connected to find a way to put in the same application the code of the GNSS example and...
Hi,
I have used the kit for weeks now measuring the power consumption of my custom hardware with the external hardware setup [1].
Suddenly the sleep currents of my target...
Hi,
I got an error BLE_ERROR_INVALID_CONN_HANDLE at the function sd_ble_gap_disconnect. I know that this error has to do with the fact that an invalid connection handle...
Hi,
I use ncs 1.9.1, and the MCU is nRF5340.
After run the timeslot some minitus, a error occurred.
mpsl_init: MPSL ASSERT: 112, 2236.
what the error mean?
Hi,
As a part of proof of concept for our newest design We have tried to setup USB CDC using nRF52840DK and NCS 1.9. In order to quickly test things out We have tried...
As a test of nrf9160 DK board, I am trying to read a voltage signal and report it to the nRF cloud. My original plan is to change a bit of the Asset Tracking sample code and...
