Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi all,
I was looking at all ble events and found a few GAP events related to security:
BLE_GAP_EVT_SEC_PARAMS_REQUEST
BLE_GAP_EVT_SEC_INFO_REQUEST
BLE_GAP_EVT_PASSKEY_DISPLAY...
Hi,
I've been monitoring the posts regarding ARM support for the various Nordic tools and libraries - and its been almost two years now since the M1 were released, and still...
I know this should be possible if the phone acts as a BLE advertiser.
But is there any way to scan for a (specific) phone MAC address, if the phone is not advertising BLE...
Hi,
I am writing the code in the cpp for bt_le_adv_start () function with BT_LE_ADV_CONN as input parameter, this helper macro is not compiling in cpp. It is throwing the...
Hello, guys!
My goal is to monitor battery voltage by using a voltage divider and ADC peripheral of nRF51822 SoC. I find that this example perfectly fits my needs. Consequently...
Hey, I found some plot difference when using write and transceive functions with nrfx library (zephyr os).
I'm trying to send 0x11 using this two codes:
And here...
Hi,
I have been mingling with kernel funtionnalities of Zephyr. I am trying to improve my application using an event based approch and threading.
I am trying to define...
We use nRF9160 on our own board with SDK 1.9.1. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We are connecting to an MQTT broker...
Hi everyone,
i'm currently developing on nRF9160DK with AWS brocker via NB-IOT connection and i don't know if i'm encountering an issue.
Until now, every time that i reboot...
sdk nRF5_SDK_17.0.2_d674dde
I used some flash to store data.
But before dfu,it was equal to (FF FF FF FF FF FF FF FF|........) and after dfu,it was equal to (29 48 0C...
Hi,
In a multi-role central-peripheral code for a nRF52840-DK based device, I have to send a buffer acting as a peripheral. I use the ble_nus_data_send function sent as...
Hi all,
I am currently trying to realize a USB to Uart bridge with the nRF52840 development kit.
I used an old sample as a starting point for this task namely the " usb...
Hi,
I need a sample project for upgradable mcuboot, I am to understand that to have mcuboot upgradable, I need to have 2 stage boot loader, wherein 1st stage bootloader...
It's mentioned in this forum that MQTT-SN may be implemented on nRF connect SDK. I would kindly ask if there is anything available about that? And will MQTT-SN be officially...
