I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using the programmer on the development kit to program my nRF9160 device.
I am using a Mac running Mac Big Sur 11.6.1
nRF Connect for Desktop v3.9.1
Programmer...
I have been having nothing but problems since moving to the nRF52840 and using Segger Embedded Studio.
I have built a project that uses the soft device, my application,...
hello nordic
i am working with nrf52840, device with zephyr and i am writing an application that uses the smp service to preform dfu over BLE.
i am struggling with calculating...
Is there implementation of these functions available for Freertos version of app_timer?
app_timer_cnt_get()
app_timer_cnt_diff_compute()
they are required for LESC...
Hello,
I am trying for connect nRF9160 on LTE-M network.
But keeps LTE searching continuously. I'm using SIM from local network. Is problem on my sim or nRF9160 dk?
...
Hi,
I'm a little confused about nfc tags.
I understand that we can use them for pairing and keys exchange.
However - what happens after pairing? Do server and client...
1. I want to put the nrf52832 into deep sleep mode for some amount of time.
2. Once it wakes up from deep sleep mode, will it affect the content of RAM or flash or any system...
This sounds like very n00bie question and I'm a bit embarrassed to ask this, but I'm not getting anywhere so I have to ask it anyway. Why my GPIOTE events are not working...
we have high current consumption when we are using Accelerometer lis3dh with SPI with no transfer at all on SPI
We have 2 SPI’s in the circuit. The first SPI is connecting...
Hi, I am using nRF5832 DK. Currently, I am using SoftDevice s132 to compile my code. I want to compile it with a different SoftDevice (say s112). But it's not working. Kindly...
Hello, We are developing a smart padlock with nRF52840 on Raytac MDBT50Q-1MV2. It will be powered from CR2 type battery. We will support two types of battery chemicals, Lithium...
My minimum requirement is 1568kbit/s .
I try the example that in Nordic\ncs_v1.7.1\v1.7.1\nrf\samples\esb ..
I increased the dynamic load to 252 ,and It can send about...
https://github.com/NordicPlayground/nrf5-calendar-example
I run the above calendar example in nrf52840 and it run successfully with no error or warning, but i did not see...
Hello,
I am using SDK1.5.1 with one nRf5340 as central and another nRf5340 as peripheral. My use case is, I am setting security level 4 (BT_SECURITY_L4) after establishing...
Hi all,
I'm recently working with Nordic devices (more precisely nRF52840), so I'm still learning. I'm working on a project where I have a shared SPI bus with several devices...
