Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I'm trying to get my head around the steps involved in doing something as simple as accessing a GPIO pin.
I'm running VSCode as my IDE, with the nRF Connect extension (V1...
I have modified the NVS sample in the Zephyr documentation to store some user data on the nrf52832 device. I'm wondering what the best practices are for ensuring the longevity...
Hello!
My issue is about setting the role for a thread device from my program, I'm programming the device using Segger Embedded Studio and the last SDK for Thread and Zigbee...
Hi community
In order to set a reasonable CONFIG_MAIN_STACK_SIZE I'd like to have a stack usage report.
I've seen the option CONFIG_STACK_USAGE . This generates an additional...
We read 3.6 V using the ADC, for our mass production devices. The error rate is about 50% of the devices show wrong values between 3,05 and 3,4 Volts.
Even though the ADC...
Considering nRF52810 for a new project with a dead-simple application. Background:
- application is just data-pipe from mobile app to UART, both ways. No encryption/decryption...
Hi Team,
we are using the I-Jet Debugger with IAR IDE , How to load the Bootloader with this setup. Is there any additional settings required for this like Segger J-Link...
I have created code in GPIO read/write code with zephyr os. I did not add GPIO in .dts file. How the my GPIO example is working.
GPIO driver is not needed .dts support ...
Hello, All,
I am using the nrf connect tool on VS code for development, but i have a questions:
The west and some other python plug-ins used by this tool are installed...
Hello everyone. I am trying to develop a communication link between two nrf52 devices. I want to collect measurements from some sensors, pack them into a single data pack...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
