Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
After looking at aws_iot sample files, I've stumbled upon the question regarding how one can dynamically change IDs and certificates for multiple 9160 devices? I...
From yesterdays question https://devzone.nordicsemi.com/f/nordic-q-a/80411/state-of-cs-ss-pin-after-nrfx_spim_xfer I have done a logic measurement and I can confirm that after...
Hi,
schematic for CFAA WLCSP mentioned, QDAA is given in the documentation. I want a reference for Circuit configuration no. 1 schematic for CFAA WLCSP mentioned in the...
Hi
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are trying...
Hello!
I am using nRF52-DK to deploy my programs. I try to use writing to SD card in ble_app_uart_central example. Both fatfs and ble_app_uart (central) examples work...
What are the memory settings in the SES compiler to compile secure_bootloader_ble_s140_pca10056
When I try to merge:
mergehex --merge s140_nrf52_7.2.0_softdevice.hex target_application...
I want to write some values to flash before the watchdog resets. For this I have the watchdog event handler specified:
In the wft_event_handler function I write a struct...
When trying to generate a new project Segger Project for my Project
in the option "Extra CMake Build Options" want to pass something like -DCONF_FILE='prj_test.conf' -DDTC_OVERLAY_FILE...
Hi Nordic team,
Looks like the most recent nrfjprog now supports flashing modem firmware.
I tried it and got some errors. Could you please point me in the right direction...
Dear Nordic Team Support
We face an issue where on different computers, using the same setup, different throughput can be achieved.
Setup:
- Custom Device using the...
Hello community...
I was able to compile the GPS sample and flash an actinius icarus (nRF9160) using the Actinius Programmer once and it said successful.
However, the...
Hi I need the upstream Zephyr project for direction finding functionality and bug fixes. Those are not present in nrf-zephyr fork.
How do I get that to work? Just replacing...
I have uninstalled and reinstalled nRF Connect v3.7.1 - Programmer v1.4.11
nRF9160 plugged into power and blinking - switch aimed at 9160 PROG/DEBUG
No devices available...
Hey, Design nRF52832 SOIC based custom PCB board and its PCBA from the machine soldering process.
When I received the board I am able to upload code using Arduino IDE...
