Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
If I set the connection interval to 300ms, can I call bt_nus_send multiple times (e.g., every 100ms) within that interval?
Additionally:
How can I check if...
Hi,
As the subject says, is there any way to get satellite count through at commands while using the AT firmware on NRF9151?
I'm currently using AT firmware version 2...
Hi
Is there a undocumented register to control the CC1/CC2 inputs?
Many power-banks switch off it's output if the current falls below a certain value (e.g. when the devices...
I am wanting to use the castellated pinouts on the nRF7002 expansion board.
I have the nrf7002eb.overlay file open and it has defined two pins that do not make sense to...
我们自己用nRF54L15做了一个硬件，和Android BLE调试助手链接都正常， 和电脑端连接大概有30%的概率能连接成功 我用的是主要报错是Failed to subscribe to characteristic: 6e400003-b5a3-f393-e0a9-e50e24dcca9e. 订阅读取数据特征失败
Hi
When l was using the function ble nus_c_string_send0 for datatransmission, an error occurred. The error code was 0x00000008.And at this point, the system resets.l don...
name:
Code:
Log1：
When the storage capacity is 64 entries, continuously reading 32 of them takes about 2 seconds.
After changing the path, run the write and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I need...
I cloned a project( https://github.com/pstrueb/hci_uart ) from GitHub and added conf files to the project. How do I know that these conf files were compiled correctly?
Hi : Here is the initialization in C:
#define SPIS_INST_IDX 22
static nrfx_spis_t spis_inst = NRFX_SPIS_INSTANCE ( SPIS_INST_IDX );
void device_spis_init...
Hi,
I keep running into an error with the following output when building the configuration for nRF52840. I thought my prj.conf would fix the issue, however, the error still...
This isn't really a problem, just wanted to bring it up in case it is helpful. I'm using the nRF Connect for VS Code Extension with nRF Connect SDK v3.0.2. I have a nRF 52...
