Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
I want to create tfm_ipc project for NRF52840 DK board.
I configured options like below.
But I got an error message, "create_nordic_project.py failed (1)...
I looked at Blinky, but I am still not sure how to access the GPIO pins. In Blinky, there is an led0 alias, but what about other pins? What are there aliases?
Specifically...
Hello,
I used SDK15.3
Android phone and iOS phone is master
nRF52811 module is slave
It's said that the phone can't set conn international（Android、iOS）
But slave...
Hi,
i am working on "nrf52dk" . i want to use nfc pin as gpio.
what i did is
NRF_UICR->NFCPINS = 0<<0;
CONFIG_NFCT_PINS_AS_GPIOS included in preprocessor definations...
Dear Nordic,
I'm doing network registration test with nRF9160 DK in CMW500 test network environment.
I've set CMW500 configuration up as described at "https://devzone...
For a Non-RTOS application, take ble_app_blinky for example, the application is coded by us while SD is provided by Nordic.
My understanding is that the SD is running as...
Hello, All
I saw this description in the Bluetooth 5 Go Faster. Go Further document：
Advertising sets have an ID which is used to indicate which set a given packet belongs...
Setup:
Module: nRF51822.
SDK version:nRF5_SDK_11.0.0_89a8197.
Example: ble_app_uart.
Softdevice: S130.
I use ble_nus_string_send on the BLE_GAP_EVT_ADV_REPORT...
I'm following the NCS tutorials. I'm targeting the 52840 on the 9160DK board. I'm using SES with NCS1.6.
I'm able to get the hello world to run and the message is out on...
Hello,
we are developing a customer product based on the nRF9160 and Nordic's NCS v1.4.2 where we need to send battery test data every 30s (~ 1kB, PUT method). The communication...
Hi:
I am working on a stereo microphone application using the NRF52840. I would like to have the 2 microphones output 16K samples per second (8K samples each for left and...
Hi,
I am using nRF52840 on custom board. I am trying to configure SPI pins, but I am not getting anything on the clock pin. I can see the chip select pin going low and...
