Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am currently working on an internal dfu modeled after the secure_bootloader_uart/ example in SDK 15.3.0. I have gotten the dfu to perform a successful dfu with the...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
Hello everyone,
I CAN NOT include the ocrypto_ecdsa_p256_public_key.h file into my project.
What are configurations I need to enable?
I'm new to NCS, could you provide...
Hi, Nordic
This is the test result that I use nRF52833 as the host to connect the slave, slave txpower = 0dbm.
And use Wireshart Sniffer to grab the air packet when...
Hi.
I recently started work on some projects where I have to use I2c OLED and BLE. I used OLED to display time which is running on an internal RTC of nrf52832.
Now I merge...
Hello sir,
i am using nrf52832 board and i am getting following error when i build the code are as follows:
1..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
Hello,
I am trying to change the device name in the ble advertisement in the secure_bootloader example.
Module model: nrf52832
Sdk: 15.2
I have tried to put...
Hello Nordic support,
I am working on a Zigbee coordinator application to make it work with an IAS zone Zigbee device.
As per the Zigbee device specification, ''when it...
Hi , I want to send a char data through bleutouth using ble nus I am using this method
I don't have any error but I don't receive any information on my android application...
I am using nRF Connect for Android and had a question about a script I would like to develop: for this script, I would like user input to specify part of the value I write...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
