Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
I am using the nfc_writable_ndef_msg example in the SDK to write from my phone to the board using NFC. I get it working successfully however, I am also trying to add code...
Hello, I'm using nRF52833, pca10100, s140.
I'm going to write a code using the external 32.768khz crystal to determine if the port is high/low every 0.5 seconds through...
