Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi ,
Need information for setting up nRF52840 on Eclipse IDE & GCC compiler . Need if any stepwise process guide available for setting up environment & debugging process...
Hi,
===========================
Chip: nRF52832
SDK: nRF5_SDK_17.0.2_d674dde
Role: Central /Peripheral
Project: BLE gateway
===========================
We currently...
Hi，
Please help me with this interrupt error
dk:PCA10095 0.11.0
sdk：ncs v1.5.0
example path:D:\ncs\v1.5.0\applications\2_hello_world_timer
example code:
test...
Hello, I have a big problem now. I set up a BLE network with 11 peripheral boards connected to 1 central board via NUS protocol. the peripheral board is based on NRF52840...
We are making a product with nRF51822;Powered by a CR2032 button battery ； Hope to achieve low power consumption;
It can be seen in the datasheet that nRF51822 has Internal...
I've been checking the nRF52805 Errata document to see which errata apply to our product and do not yet have a workaround implemented in our firmware.
Unfortunately, I'm...
Hi,
Device FW information is as follows: SoftDevice: s113_nrf52_7.0.1_softdevice.hex bootloader: mesh_bootloader_serial_gccarmemb_nrf52832_xxAA.hex device page: device_page_nrf52832_xxAA_s113_7...
I want to use our app in phone to communicate a nrf5340 board through ble. my project use sample peripheral_uart . but app ble three 128 bit UUID is different from ncs1.5...
Hi,
I'm trying to measure and log the low power coming from a peltier module. (TEG seebeck effect). In Ampere meter mode with LED for load I get nothing. Replace TEG with...
Hi,
I successful developed a application using nrf / zephyr SDK and install the applications on the nrf52840dk and dongle. Now I want to adjust the power using
CONFIG_BT_CTLR_TX_PWR_PLUS_3...
hello i am trying to interface RN8209c ic with nrf52832 using uart communication with sdk 15.2
uint8_t readbuf[50];
uint32_t err_code;
uint8_t buf[10]; buf[0]=0x7f;...
Hi,
I am trying to modify the Android nRF Mesh app to filter un-provisioned devices with URI hash contained on un-provisioned device beacon.
My question is how I can...
Hi
I have a question, the Nordic SDK have a DFU, I want to know what is the default value of TX power in Bootloader? Can we change the TX power? if yes. How to change it...
Hello, I'm using nrf52805. It is confirmed that P0.04 is AIN2 and P0.05 is AIN3. Can I use this pin as UART TX,RX? What should I do to use it? Thank you.
