Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I'm working on an application that utilizes CLI library, and I need to add CLI commands as in the code below:
But when I attempt this I get an error message:
error...
hi ,
I am working on I2S to collect audio, and I need 2 nrf52833 to realize the intercom function. For these two nrf52833, the I2S clock is different. There are fast and...
Hi,
I add NFC to my project with freertos. The initialization of nfc is ok. After running few seconds ,it hang. If I comment the usr_nfc_init() that in the main() function...
I have a legacy SPI device that works well with an nrf52 application using nrf_dev_spi_transfer ()
I want to use the same device from an nrf9160 application.
The problem...
In Nordic's Zephyr fork (sdk-zephyr) there's this GPIO driver function:
I don't think this is the entire story of querying GPIOs, though. This appears to only query...
Hi,
I'm trying to interface NRF52DK with Quectel EC20 Evaluation board through UART. I used the example UART code from the SDK to send AT commands to the Quectel Board but...
Hi,
I'm looking for information about FOTA capabilities when upgrading firmware on secondary mcu devices.
for example ->
fota = web(cloud) -> (mqtt/http) -> (nrf9160...
Hi,
You specify that S132 v7.2.0 is qualified as QDID 138862 in this link:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832...
Hi, I'm just a new user for nrf connect SDK. I use v1.5.0. When I try to build the solution on SES, I get this error.
I saw a post like this also. But I don't know how to...
I am developing a project on the ble_app_template example. In the sdk(15.3.0) example, when the button is pressed, some cases are executed by going to bsp_event_handler. if...
Hi,
I use examples : nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs;...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
I am trying to source nRF5340 chips from Digikey.
I can see the link to the early Enggineering A version (AB0), which we absolutely do not want to buy
https://www.digikey...
I tried to upload the hello world program to the thingy91s nrf9160 via nrf connect programmer app over usb. Unfortunately it didn't work as excpected and the nrf9160 doesn...
