I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Due to some error, I lost 2 factor authentication key on my other account and cannot login from there. I want to recover that account or delete it. Please help.
There is no category for this problem. But the devzone has great information but a horrible user interface riddled with headaches.
1. Pet peeve #1: Trying to enter tags...
Hi,
I'm trying to evaluate the new Asset Tracker v2 example with a Thingy91, nRF cloud, and the supplied iBasis SIM, but when I build I get the following error:
C:/Nordic...
Hello,
in documentation of nRF9160 RSRQ is defined for 0..34 and 255.
What about values 35..254? Is it possible to get these values from the chip?
I have to know, if...
using any example with BLE I get the following:
when loading , prints on log :
[00:00:00.291,595] <wrn> bt_hci_core: ECC HCI commands not available
and when I...
Hello, Nordic.
I'm configuring a mesh network. The provisioner, client and server all going well, except for one problem.
I made a client and server based on sdk-coexist...
Hi
I connected EEPROM and RTC to nRF52832.
The interface is TWI.
I'm looking for a sample program to evaluate this EEPROM and RTC.
EEPROM wants to read, write, clear...
I am going to programme the nrf52840_pca10056 DK with Arduino IDE. I was folow this tutoriol https://how2electronics.com/nordic-nrf52840-advanced-bluetooth-5-arduino-ide/...
Hi,
I am trying to set up a bootloader using the example code given in SDK 15.3.0. I am working with the nrf52840 dk and have been using the same device with the same project...
We are working on requirements for a design based on the nRF52832. Does Nordic have characterization data to share of the temperature dependency of clock drift of LFCLK?
Hello all,
I've got a Thingy 9.1. I've successfully built and flashed the serial_lte_modem example (with no changes) onto the device but when I open the serial port in LTE...
Hi,
I dowloaded mesh 5.0 sdk and open light_switch example project with SES which installed in a 64bit windows 10.
I set the SDK ROOT as following the step of online guide...
Hello,
I have just started in the world of Nordic products and quite recently in the embedded world. I'm trying to learn and understand the use of zephyr in basic projects...
Hi,
after migrating functional project to latest ncs version v1.5.0 I managed to build and flash it to nrf52840 board without problems. However if I enable MCUboot option...
