Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I am attempting our custom hardware based on an nRF52 chip.
nrfjprog returns the following error message:
ERROR: JLinkARM DLL reported an error. Try again....
Dear Sirs,
We are currently considering to put nRF5430 SoC in our next generation gaming device. One possibility to develop the firmware for nRF5340 SoC would be to use...
Hello,
I have just started learning nrf. I have an nrf52832 board and I want to get and set time using app.
I have seen this https://devzone.nordicsemi.com/f/nordic-q...
Hello
I would like to change the "Company ID" in my application so that it is no longer Nordic's (my application is based on the ble_thread_dyn_mtd_coap_cli example). I...
Hello
I'm contacting you because I'm having a problem connecting to devices that use the ble_thread_dyn_mtd_coap_cli example. Actually, I have no problem when I connect...
Hello all,
I am working on nrf52832 and i need to use the nrf_crypto librariy. The example uses nrf_crypto_aes_crypt and nrf_crypto_aes_finalize function. Although they...
As title, I would like to measure an API function execution time. First method is to print the timestamp before and after the API and the second is to use GPIO and measure...
Hi!
We are developing a board with nRF9160 and want to use it on NB-IoT mode.
The development is made in Romania, Cluj-Napoca and here we have no problem with it. Even...
hello sir/madam .
i am going to implement the code to master and slave clock communication , iam connecting the one nrf52 module to the master clock (through wire controller...
Hello,
I guess it is a simple problem, but I am new to the nrf world, so here is my issue:
I want to use this code to switch on a LED by pressing the on board button...
Hello, I am starting a project and I want to know what is the best way to achieve this. I am using nrf52832, I have the DK as well as custom board. I want to receive an image...
Hello Noridc Support Team and All members,
I am new to BLE development.
I am using the nRF52 development kit and the SDK v17.0.2
My intent is to send the sensor data...
I was studying the Wireshark BLE sniffer packet parsed data for a "Find By Type Value Request" and noticed that the Value was not parsed as Little Endian so it was given as...
Dear Mesh Experts, what's the recommended approach to recover lost mesh keys? Imagine, for example, an industrial mesh installation with hundreds of nodes, all provisioned...
