Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
As UE HW designer/manufacturer we have limited possibility to troubleshoot modem/EPC states.
We had troubles with MME switchover and other corner cases recently.
We would...
Hi Sir
Now we have a project with NRF52805 and will MP by 2021 May,
We are looking for a RSSI test method for production line,
Currently, we are using a Litepoint IQxel...
Hi,
I wanted to use the project code of nrf5832 which we have created with nrf17.02 sdk and nrf5.0 mesh sdk with softdevice 132 for the board nrf5840 board. We are stuck...
I need to get quite a lot of logs and quite fast too. How do I do I get the logs into a file?
I tried with Segger RTT logger, but it tends to give up quite quickly. I heard...
I want my system to sleep for some time, but its waking up and I am unable to understand which interrupt occurred. I want to know which interrupt caused the system to wake...
Hi All,
I want to implement a function to send data from the internet coap client to nrf52840 DK coap server. The nrf52840 runs .hex file which is one modified from Nordic...
Hello, I'm testing an example of a zigby light bulb with a nrf52840 (pca 10056) board.
Here, when I press "BUTNERT 1" on ZED, I want to send the [ON/OFF] status of the current...
The average current during the nRF9160 test DRX is 2.2mA. The period of DRX is 2.56s. Using a China Mobile IoT card. I am testing on the DK board and have turned off all peripherals...
I used NRF24L01 to transmit the data without ACK mode. The receiver received the data normally when only the WR_TX_PLOAD_NACK instruction was used to send the data.If the...
Hello,
I want to set a GPIO Pin to high. Therefore I wrote the code below.
But when the software is written onto the nrf52811, I can not messure any voltage.
I do not...
Hi,
I am going to do data communication between two boards with libuarte. I see that both txdata and rxdata should be uint8_t*. But if I try to transmit the char*, will...
Hi On a nrf9160, I need to send data via UART(E) at 921600 baud. According to the UARTE BAUDRATE register documentation the register value 0xF000000 (Baud921600) leads to...
Hi,
I changed application main.c to enter in to DFU mode after 20 seconds. System is reset every 20 seconds and the boot messages are printed. The message "Booting (0x8200...
I am trying to measure distance with a vl53l1x sensor through the twi_sensor example. I uploaded the code to segger by referring to sparkfun, but twi_handler does not work...
