Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Thanks in advanced. I update uart pin number to rx:10 and tx:9, then get the error as title described under DEBUG mode. To save power, I use uart but uarte, so I set UART_ENABLED...
Hi,
I'm using the SAADC to sample external voltage to fill in the battery service. I have use APP_TIMER_DEF to create a timer to do it every 30 seconds. Also I have init...
I'm developing a Peripheral with a rather intricate connection process and doing a lot of testing.
I find that if a Central connects, and then the Peripheral tries to send...
Hi,
I have to implement customized services in my project.I think it is better to have seperate files for service inititialization.For that purpose I have seperated service...
This (in SDK v17.0.2):
Experimental: BLE Interactive Command Line Interface Example
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ble_sdk_app_interactive.html...
Hi
I have a coupe of dongles working on a project. While validating the board, i notice a strange behavior: I have the dongles in factory reset (MBR at start, the Bootloader...
Good afternoon
i have built a small program for the uarte, using the example however im not managing to edit the event handler such that depending onthe text i recive...
Had tried to build it from the IDE before. Couldn't do it. Tried to build manually, got exactly the same error I was getting in the IDE. Parsing C:/Users/mario.raposo/zephyrproject...
Hi,
i have followed a few manuals like this one: https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/GetStarted#infotabs
or this one:
https:...
I'm trying to make an application which displays signal transferred via bluetooth.
To reduce computing time on the tablet, I want to apply oversampling in nRF52840.
The...
Thanks in advanced. I achieve 4 uint8_t dynamic sensor datas, I want 52832 transmit them through BLE continuously. Based on examples\ble_peripheral\ble_app_gatts_c, I can...
Dear,
How to evaluate a channel if is clear in property in NRF528 serials? e.g. there are ED and CCA in 802.15.4 standard, how to implement CSMA in NRF52810?
Hi
I'm using nRF52832, SDK 16.
When I enabling timer application the power consumption is increased by ~450uA, far away from the product specification
What may cause...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
