I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have a question about "Importing Keil projects".
I want to run "ble_app_multirole_lesc (SDK V14.2.0)" using "SEGGER Embedded Studio". However, there is no project file...
Hello,
Currently, I have a product with the nrf52832 SOC and my customer wants to know its life-cyle.. (approximately)
just to take into account possible replacements...
I have a question about LE Secure Connections(LESC).
Is it possible to pair with multiple devices in multi role operation? I am considering the following connection. ・Peripheral...
I'm using ble_app_uart_c example with NRF52840.
And i want to read the beacon device id( 8 byte ) at Central(nrf52840).
The ADDR value could be verified through the questions...
Hi, i'm using nrf52832 uploaded ble_app_beacon example.
I want nrf52832 to work as a beacon and as a nfc tag.
Thus, I added some nfc example code. nfc_t2t_lib.h also...
I'm investigating a failure in 2 devices. The devices are immediately failing in application start-up due to fds_init failure. I tracked the failure back to fds pages_init...
Hi,
I could not find the logic for spi_xfer_done flag (main.c) that is being updated after SPI transfer is done in the SPI example from SDK 15.3.0.
There is no particular...
In light switch example, I am trying to implement relay feature. I used nRF5_SDK_15.2.0_9412b96, nrf5_SDK_for_Mesh_v3.0.0_src.
When compiled light_switch_client_nrf52840...
Hi,
I am using modem version 0.7.0-29 alpha modem firmware. ( I have also checked with 0.6.8-131 version )
I have already done MQTT connection with Azure IOT hub and...
I need to increas the speed using the UART ove BLE application.
I try to add new characheristics to the Nordic UART Service.
I have added the UUID for this new charactheristic...
Hello,
I would like to get AT Command Sample to work on nRF9160. I erased the module using Programmer software "erased all" and then loaded Secure Boot sample, then updated...
Hi,
I have successfully set up the nRF Sniffer V2 Beta 3 using nRF52-DK (PCA100040). It works very well with Wireshark integrated toolbar, I can select the specific device...
Hello,
I am running a secure bootloader on the device and want to use the nRF Connect Desktop tool as DFU server to upgrade the device firmware. I launch the "Bluetooth...
Hi,
We are developing a GPS tracking device using nRF9160 module.
We want to use a battery as long as possible maybe for 7 days.
Here we need two cases for our application...
