Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Using the 15.2 SDK, the stack generates an error when attempting to bond. I am using the android nRF Connect test app to initiate the bonding after connection. The error generated...
I'm using SDK 15.2 & HID keyboard example. I would like to know the following things-
1. How long does BLE chip advertise its name before making a connection with central...
Hello,
We're currently preparing for BLE certification of our device. It contains an NRF52840 on a custom PCB, so I believe we'll need to perform RF-PHY testing for certification...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi! I develop board based on NRF52832. P0.08 is connected to the MOSFET transistor.
The transistor switches the relay. During start (power on or reset) on GPIO there is...
Hello,
Please let me check about the usage of an IRK for the default setting and how to change an IRK each bonding cycle.
We use the resolvable address for our application...
Hello
I have a setup with 3 nrf6310 dev kit and with a nrf24LE1 module on each of them.
1 acts as a transmitter and the other 2 act as a receivers. What I specifically...
Hi
I am using nrf52 DevKit and was able to load the \examples\ble_peripheral\ble_app_beacon program on it. I am able to see the beacon RSSI, major and minor values. Now...
Hi,
I am using Nrf Sdk Mesh V3.1.0 with softdeviceS132 and sdk board Nrf52832
I am trying to implement Normal DFU in Mesh network.I don't need Mesh DFU.
So i have added...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I am bit confused between fds_record_update...
Hello, I am using AES -CCM encryption in my program. I want to know about memory like does it need any dynamic RAM ? In example code I found 'nrf_mem_init()' but unable to...
Using: NRF52832, SD 132 6.1.1, SDK 15.3.0, Mesh SDK 3.1.0.
Hi, I included mesh_opt_core.h in a C++ file, and got compiler errors at NRF_MESH_STATIC_ASSERT().
I fixed...
Did current OTA only can dmostrate "ble_app_hrs" and "ble_app_rscs"? Other SDK5.0.0 examples?
I want to try ble HID keyboard. So, deliver the hex file to celluar phone and...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
