Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I am trying to operate a BLE5 sniffer with nrf52840dk
After connecting the dk to nrf connect desktop and programming it with a wrong code (by mistake), it is not able to...
I'm using the nRF52840 DK.
I managed to burn the on-board nRF52840 MCU several times, using the nRF connect windows app.
After several such successful burns, with various...
Hi,
According to the datasheet:
Does this mean that when i change my vdd from 3V to 2V, then the current peaks will be reduced? If so what does this:
graph means...
Hello,
I'm currently designing a custom bootloader to perform a DFU. So far I'm able to update the bootloader and the application, however there is a problem when I try...
I have been studying MQTT these days.
I'm testing the program below. https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/mqtt_simple/src/main...
I use nrf52832 sdk15.2 to develop products, use WDT to prevent program crashes, WDT set time is 10S, nrf52832 will be paired and bound after connecting with IOS phone, when...
Hi!
I am trying to use the SAADC driver on SDK13, following some examples from the playground repo. I am using the app timer to trigger a measurement for 4 channels. ...
Hello,
I cant seem to find a PBKDF2 function in the SDK to generate a private key from a passphrase.
We want to use mbed-tls or CC310 to make a SHA512 based key for AES...
Hi Everyone,
I have a custom board with nRF52840 and am testing out basic GPIO functionalities with some LEDs. In the board, the LED cathode is connected to nRF52840 GPIO...
Using nRF Connect for PC Version 2.6.1
Connect to a peripheral device that ask for an ATT_MTU > 247 bytes
NRF Connect fails with
Failed to call gattsExchangeMtuReply...
Hi
I have implemented (heavily base on the found examples) an application which uses both ESB and BLE. For now I focus on developing the ESB part of the SW. I am using the...
Hi Sir,
According to the nRF52832_PS_v1.4.pdf, In section 17.1.1, the table shows the current consumption of Radio. What's difference w/ Iradio_tx0 and Is0? Why do we get...
Dear Nordic Team,
We are building a very low power wearable with the nRF52810, only powered by a small solar cell and a super-capacitor.
We would like to offer firmware...
Hey,
I am working on nRF52 DK boards. Suddenly PC is not detecting the one of my DK board, but the nrf53832 processor's LEDs are functioning as per the last program dumped...
I am trying to use multiple channels for beacon transmission.I want to hop to a different channel at an interval of 2 seconds.I have configured one device as a pan coordinator...
