I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have couple of nRF52-DK boards which I think got damaged by accidentally getting reverse voltage.
I have tried to analyze and detect which part would have blew up by testing...
Hi,
I have successfully done one publisher and one subscriber example by using mosquitto broker on raspberry pi and 2 nrf52832s. What I want to do is that I want to send...
Hello, I have a very basic question:
Are Bluetooth nRF5x products compatible with other manufacturers? For example, can I have an nRF51 dongle communicate with a Microchip...
There are two APIs in SDK 14.2 to access the nrf52832's AES core. What's the difference in behavior between the two?
I noticed that nrf_ecb_crypt() has a useful return value...
HI:
I Select the SDK11 as my BLE master.
" nRF5_SDK_11.0.0_89a8197 \ examples \ ble_central \ ble_app_multilink_central \ pca10028 \ s130\arm5_no_packs ".
I Select the...
Hello,
I use NRF52832 and nRF5_SDK_15.2.0 for our custom board.
Also, FreeRTOS(Tickless IDLE is enabled) is used. And, System ON mode is used for sleep mode.
Now,...
Hello,
I am trying to send data from nrf51822 through UART TX to esp8266. I've gone through the app_uart examples and I can recieve data through RX but having difficulty...
Hello,
First, I follow this tutorial --> https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . It's working well on the...
Development Environment: Segger Embedded Studio 4.16
Debugger: Segger J-Link Lite/ Segger J-Link Pro
Debugging a custom nRF52810 board using SWD interface.
I am experiencing...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
