I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I followed this tutorial :Bluetooth low energy Characteristics, a beginner's tutorial
i am beginner to study BLE.
I wanna the answer Challenge 1: Why are you not allowed...
Hello,
Our setup:
IDE : Segger Embedded Studio for ARM V4.12, nRFgo studio
SDK : nRF5_SDK_15.2.0_9412b96 + SDK for Mesh3.1.0,
Softdevice : 6.1.1
Computer Platform...
Hi, I'm using SDK12.1 example ble_app_ancs_c.
Is it possible keep advertising (non-connectable is ok) when ancs connecting?
And how to do it?
I tried call advertising_start...
Hi,
I have been having issues with the compile hex files I get when following the steps to build the pc-ble-driver (). While I am able to build the hex files when I place...
I got Orange sim connected to LTE-M network on nrf9160 DK, verified it on LTE link monitor. But when i tried adding a LTE device on nrf connect cloud, i am not able to register...
Hi,
I tried to build the lte_ble_gateway sample in SES, however it gives the error below regarding the UART.
Any suggestions how to resolve this issue?
Hi,
As mentioned in the subject, I am confused with the SPIS example from nRF52 SDK 15.3.0. I wonder where NRFX_SPIS and _INST_IDX are defined in the header file?
SPIS...
Hello,
I am testing the Light Switch example and I observed a problem:
- I noticed that it was possible to reset the "server nodes" by pressing their "button 4" to leave...
I am having an issue migrating some code over from Keil to an example in SES studio.
The code in Keil is simply listening for a radio packet, when it receives it, it transmits...
Hello,
I generate a private key by using nrfutil.
I like to convert raw data format to use in the code from private key.
Additionally, I already used a nrf_crypto_ecc_key_pair_generate...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
