Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I just finished reading the O'Reilly book " Getting Started with Bluetooth Low Energy: Tools and Techniques for Low-Power Networking " where the author uses the nRF51822-EK...
I could run the examples like blinky just out of the box
But, I am clueless how to add a bootloader to this example. I just want to add a simple bootloader from Open Bootloader...
Hi,
we are about to enter bluetooth and expand our products with it. however, the approval process still raises some questions. What I have understood so far (please correct...
Hi everybody,
as already mentioned in the title, I guess to have stumbled across an incompatibility between the app_pwm library and the gazelle link layer.
To keep it...
Hello,
I'm using SDK 15.3.0
I added "err_code=sd_ble_gap_adv_data_set(p_data,31,NULL,0);" to the advertising_init(void) function, but I got the following error:
Error...
MCU: nrf52840
SDK: V 15.3.0 with nRF-IEEE-802.15.4-radio-driver
problem:
I tested repeatedly connection with my nrf52840 production (peripheral) with andorid phone...
Hi,
I have downloaded MDK Keil software .so the problem is if i click on + sign in all devices in pack installer it is not expanding and also i am getting like this
if...
Hello All,
Greetings!!!
I am working on nRF51822. I am used custom board. For reference i used nRF52 SDk 8.1.0 in IAR.
Right now i am use gpio pin as an interrupt pin...
I send 25 byte long messages to unicast addresses in a Mesh network. Because of their size messages become segmented. access_model_reliable_publish() is used for sending....
Hello,
I am using a combination of several Nordic devices and hardware. The nRF52832 is used in a sensor to collect light level information. That data is transported over...
Hello,
I wrote a simple program to turn on externally connected LED at Port 1 and Pin 10. But it is not working. See the code -
#include <stdbool.h> #include <stdint...
Is there any documentation about how to configure the SoftDevice clock configuration using the RC as SoftDevice clock source?
My target is the nRF52832 with the S132 Softdevice...
Folks,
We're wondering how the soft device can work with it being provided as a hex file? Usually with things like this you'd get object code to link to, but that doesn...
Hi,
I am currently working on a project for which I use the Secure Serial UART Bootloader from SDK 15.3 (nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart...
