Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
Hi,
I am using esb project of SDK15.3 to test esb PTX and PRX function.
The default setting of address-0 and address-1 is 0xE7E7E7E7 and 0xC2C2C2C2, and PTX and PRX can...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
Dear nordic,
I need more information regarding this?
1. I heard the BLE one packet has possible 20 bytes. but i tested this example and connect using nRF connect app...
Hello everyone,
I am experiencing a weird problem; I am working on an NRF52840 DK board and writing my code in Segger Embedded Studio.
I do not have any problem when...
Hi,
I am looking for the nRF52 / nRF52 Mesh online courses.
I am going to developing a new project based on MESH network. where i required lot of sources to clarify my...
Hi, I'm using the nRF52 SDK 15.3.0's BLE_APP_UART central/peripheral examples with my PCA10040 boards.
Can I ask about the central example, please?
0. Currently, I think...
