Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
We are using an nRF52832 (silicon REV C) microcontroller and we see periodic current spikes in between BLE advertisements... our power consumption is higher than...
Hey, I use nrf52 dk with nrf5 usb dongle. I am using this ble_app_uart__saadc_timer_driven__scan_mode example, I think it is working just fine, but the values are in hex-format...
i am not able display uuid, major,minor values and company identifier(so that we can change the beacon identification to ibeacon) using Ble_app_proximity example. please say...
Does the current background DFU support (if not is there a plan to support) Bootloader and SoftDevice updates? It will be extremely useful to update the BL and SD through...
Hi,
i'm using nRF52832 there is easy way/tutorial/explanation how to make it to connect as a client to the mesh app mobile using ble_app_uart_coexist code?
Thx.
Sir,
Writing Android Software to receive bytes from one of your ble chips for the UART design. Editting nrF ToolBox app.
UARTService.java
onDeviceConnected(BlueTooth...
Development Software: SDK v15.3, IDE IAR v7.8, SoftDevice 6.1.1
Computer Platform: Windows
HW revisions: EYSHJNZWZ (nRF52832)
Hi,
My application requires SPI and...
Hello Team,
i am evaluating Custom software Codec inside nrf52840. need development help whether it supports custom codec or not? which bluetooth stack used for development...
I'm working on a NRF52832 project with SDK V15.2, using S132 Softdevice. before connecting, nrf_fstorage_write/nrf_fstorage_erase/sd_flash_write/sd_flash_page_erase all are...
Hi.
I am using SDK15.0.0.
I tested the RF communication through the ESB example.
And I have tested the BLE communication using the ble_app_hids_keyboard example. ...
Hello all
currently I am flashing the device using command line:
#erase chip nrfjprog --family NRF52 --recover #program softdevice nrfjprog --family NRF52 --program...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
