Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I am using a sniffer on nRF52840 DK between by central and peripheral device. The frequency of packet transfer is at 433MHz. Can the sniffer detect the packets at the...
Hi everybody,
I am currently trying to write in flash several records key in a same file using fds_write, fds_update, fds_records_find.
My page is FILE_ID = 0x1000 and...
Hi,
I have an application which scans for BLE advertisements and pushes some information about it over UART.
I run this on a nRF52840 DK card using softdevice s140 6.1...
Now, I have a project that needs to do a master device to communicate with another slave device, but the slave device is done by the customer. I found that my main device...
Hi,
When trying to connect various thingy's to an Android with the Thingy SDK, the debugger gives me that :
D/BluetoothGatt: onClientConnectionState() - status=8 clientIf...
Hello ! So i have a nrf52 device, and i would like to know if there is a possibility to us it as a multi hub devices. ie: two nrf52 devices, one programmed with ble_app_uart_c...
Hello Everyone,
I am building an application where I have to change the scan window (BEARER_SCAN_WINDOW_DEFAULT_MS) in run time, based on a specific event. Does the stack...
I cannot find any useful information on the purpose of this project: examples\connectivity\ble_connectivity\pca10040e\ser_s112_hci (and likewise with other boards & SoftDevices...
Hi all,
I have a hard time to merge Mesh Proxy Service and Nordic UART service. I am working with mesh SDK v. 3.1.0 and nRF5 SDK v. 15.2, coexistence example ble_app_uart_coexist...
I am considering using BLE advertising for sensor devices as peripherals and using a mobile phone as receiving device.
Because the number of sensor devices can be more than...
The current protocol for the mesh serial interface as documented here:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk%2Fdita%2Fsdk%2Fmesh_sdk...
how to program an nrf51822 chip(chip with ou coin cell battery the rectangular chip not circular) using nrf51-DK to work as a beacon .. kindly share me the detail process...
using nRF52832, SDK 15.1, custom made units.
My Obervations - (in bootloader settings) $nrfutil settings display ota46to47.hex
when device is flashed "Current bank"...
Hello,
For BLE mesh light_switch example, the following statement is showing error.
In app_config.h
#define NRF_SDH_ENABLED 0
In sdk_config.h
#ifndef NRF_SDH_ENABLED...
Can someone tell me how to make device go to sleep and make it wakeup after a few hous using systick timer. I know how to create a timer but i wanna know which system call...
