Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Dear Community,
I am working on the following application: using the RaspberryPi to flash over-the-air nRF52 nodes (Nordic's Secure DFU BLE bootloader)
For that I have...
Hi all, I have 2 module NRF52832.
Module 1: I using BLE and ESB at the same time, so I request timeslot for ESB, mode RX
Module 2 : I not use BLE, so I can't request timeslot...
Hi,
I added DFU functionality to my Mesh-client application as shown in your DFU-example.
At startup I get this log message:
nrf_mesh_dfu.c, 904, ERROR: No CMD handler...
We have been using the Nordic nRF52840 Preview DK to work with our debugger vendor, iSystem. On page 32 of nRF52840_DK_User_Guide_v1.3.pdf, lists TRACEDATA[1] being connected...
I'm adding the peripheral/RTC project to experimental/CGMS. I cannot seem to get past ASSERT in nrf_rtc_prescaler_set. I changed the prescaler from 4095 to 0xffff as I suspected...
Hello,
I try to build a working firmware for reading some parameters from external sensors and transmit them thru BLE (I am using S130 and SDK 12.3.0). I have already developed...
I am using nRF5_SDK_14.2.0_17b948a on a Fanstel BT832 module which is having nRF52832 SoC. And I am using s132_nrf52_5.1.0_softdevice.hex .
In my application, I need to...
I modified the "ble_app_uart_c" to connect HM-10 (using TI BLE chip CC254x) SPP peripheral.
Ignoring the filtering process (make function adv_uuid_compare(nrf_ble_scan.c...
Downloaded from Git Hub nRF ToolBox from GitHub project dated Nov 12 2018
Tried to build with Android Studio 3.3.2 JRE 1.8.0.152
But get build error
Error C:\users\maltr...
Hi,
I use the nrf52 to connect to a central using BLE 4.0 where power consumption is a sensitive issue. I want to understand how encryption will increase the Link Layer...
I use pc-ble-driver-master/hrc as central to connect the target device which runs with modified ble_app_uart hex.
I can discover service and characteristic correctly, but...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
