Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am working on the Mbed-OS HAL implementation for the nRF52840 USB device.
I have it almost passing all the automated tests. One where it fails is when the Mbed test suite...
Hi,
Since the moment I installed and configured eclipse following this tutorial: devzone.nordicsemi.com/.../
I was never able to successfully debug any of the programs...
I have combined the ble_app_uart_c with mesh light switch example. In the file nrf_drv_uart.h it does not show the same "active defines" as with the original ble_app_uart_c...
hi...
i want a simple message model for mesh sdk latest version 3.1. From this post https://devzone.nordicsemi.com/f/nordic-q-a/37269/using-simple-message-model i have download...
Hi,
I intitialized PWM1 instance:
I use PWM1 to generate constant PWM signal with nrf_drv_pwm_simple_playback(m_pwm1, &seq, 1, NRF_DRV_PWM_FLAG_LOOP);
I also initialized...
Hello,
I have a nRF52840 DK and a nRF52840 Dongle and I want to probe the throughput example using them. But I don't know what is necessary to adapt from the example code...
Hi,
What are the options to measure the execution time of code snippets? I used app_timer_cnt_get() now and is giving 50 ticks for 1ms. Is there any way I can measure lesser...
Hello everyone,
For simpilicity,assume i have a node that is connected to an esp32, that node is configured as a coap client(actually its a node that gathers coap requests...
Hi,
I am trying to get the CRC error packets during nrf_ble_scan_start execution with nRF52840 DK (nRF5_SDK_15.2.0_9412b96) as following:
ble_stack_init();
scan_init...
I am following the readme for nrfutil on generating a package file for the secure DFU. I am using the debug version of the bootloader which comes with a predefined public...
nrf52832.
SDK14.2
Segger ES V3.34a
With an initial prototype batch of 30, we have noticed 4 modules that have incorrect voltage readings, reading low ("Bad Modules...
I didn't recieve answer to my second question in this topic , so I start new one.
Is there any way to get usec time measurement with softdevice?
I need to analyze SENT...
Hey,
I have PSELP of the ADC configured to read 4 values. now I want to configure an ADC channel differently than the excising 4 channels. So can I configure the 5th channel...
I am using the nRF52832 in Rigado BMD-301 module. Updated to s132_nrf52_5.0.0 and nRF5_SDK_14.0.0_3bcc1f7, built the ble_app_uart_c without any changes and programmed it on...
Hello,
I am working in a Windows 10 environment with the latest SDK 14. I use the Segger IDE and the various support tools from Nordic (nRFGO, nRF Connect, nRF Master Control...
