Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, there is a code comment "Workaround for PAN_028 rev1.1 anomaly 22 - System" in nRF5_SDK_12.3.0_d7731ad\examples\proprietary_rf\esb_low_power_ptx\pca10028\blank. So, I...
I would like to do I2C BlockRead using nRF52.
devzone.nordicsemi.com/.../i2c-block-read When I looked at it, I found that it was not possible to receive variable length...
Project migrated to SDK 15.3.0 with Softdevice S340 6.1.1
Project is using DFU secure bootloader. The example in "dfu/secure_bootloader/pca10056_ble" was used as the starting...
Dear nordic,
I have some doubts regarding PWM. i want two PWM out both are working different frequency and also i need softdevice. I think PWM can make two ways one is using...
Hello,
I want to change the 16-bit of 128-bit UUID at runtime. is this possible?
let me explain...
1)the first both central and peripheral set 128-bit UUID like this...
Hi,
Actually i m new on this field.
I m making indoor navigation by using nrf52840 soc.And i m using sdk15.2.In that sdk i used beacon app code for advertising beacon...
Hi.
I use a modified lightswitch server application with Nordic SDK 15.2, Mesh SDK 3.1.0 and Softdevice 6.1.1.
During provisioning I experience a software assert with...
Hi,
I want the bit rate to be 125Kbit or 500kbit. The project uses 1Mbit and 2Mbit. I'm investigating the topic on the Devzone blog. I reviewed the example nrf52840-long...
My work need to use 4 gpio interrupt, but it not work when use freertos on nRF52832 ,sdk version 15.0.0. My code is like below:
err_code = nrf_drv_gpiote_init();
nrf_drv_gpiote_in_config_t...
I created own app button library. It's just return handler into main with number of pin and type of push - short or long. Also I created library for rgb_led (using nrf_pwm...
Hello everybody,
I'm using nRF5280 (Laird BL654) with SoftDeveice S140v6.1.0 and SDK 15.2.0 with a modified version of the blinky peripheral example.
I've changed NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello
Our custom board has two chip configurations for BLE stack. The two chips communicate with each other through UART. Both chips are running zephyr with two chip configuration...
I'm writing an app to that talks to the Thing52 over BLE, and using this as a reference: nordicsemiconductor.github.io/.../firmware_architecture.html For Battery Services...
Hi,
We just recently bought the nRF9160_DK board and compiled and loaded the AT_Client onto the DK. We have followed all the setup instructions for the SIM card for iBasis...
The example code of beacon was used from the SDK - nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs\ble_app_beacon_pca10028_s130...
